How To Set Up A Coleman Pop Up Camper

Download Article

Download Article

Setting up a new pop up camper at a military camp for the get-go fourth dimension can be a bit intimidating. By keeping all the steps in social club using this helpful guide, you volition before long gain the confidence to prepare your camper with no problem at all.

1. ane

   Position the camper where you would like information technology to be on your campsite. Do not unhook your tow vehicle yet. When selecting the location, consider things like:

   • Slope of the basis (you can merely adjust level so much)
   • Location of copse (don't desire to hit roof when raised or beds when pulled out)
   • Proximity to the burn down pit (give yourself plenty room)
   • Location of electrical hookup if using one (make sure your cord is long plenty)

2. ii

   Bank check side to side level of the camper. ^[1]

   • If it is already level you lot tin can skip to blocking the wheels.
   • Note which side is low. This volition be the bicycle yous volition need to level upward.

   Advertisement

3. iii

   Move the camper either direct forward or back approximately 1.5 feet. This tin be hard to cuff at showtime then information technology may exist helpful to have a spotter watching on the outside until you go the hang of it.

4. 4

   Place a slice of plywood, approximately 1.5 feet long and wider than the width of the camper wheel, in the spot where the wheel was before you lot moved the camper.

   • Stack more than one piece of wood if the site is particularly unlevel.
   • There are commercial leveling blocks bachelor but plywood works just fine and is probably cheaper.

5. 5

   Movement the camper and so the wheel is centered on top of the plywood yous just placed downwardly.

6. vi

   Recheck side to side level. If it is still unlevel repeat the step where you movement the camper and then add more plywood. It is good to take a supply of at to the lowest degree three to v pieces of plywood to stack if the spot is particularly unlevel.

7. seven

   Place pocket-sized blocks of forest in front and backside both wheels one time your camper is level side to side. These can exist merely cut upward pieces of two by four. The purpose is to keep the camper from moving when you unhook your tow vehicle as well as while you are camping. One time again, there are commercial blocks available but wood blocks work just fine.

8. eight

   Pull the retaining pin and swing downwardly the camper tongue jack.

   • The tongue jack is at the forepart cease of the camper next to the propane tanks and battery.
   • The retaining pin is located at the midway point on the natural language jack.
   • Brand certain the natural language jack is retracted enough to enable it to swing to the full down position.
   • Place a slice of forest underneath the jack cycle if yous are camping ground on sandy or other soft ground to keep it from but sinking into the sand.

9. 9

   Unplug the electric connection from the tow vehicle to the camper.

10. 10

    Unhook the safety chains.

11. xi

    Raise the camper tongue off of the tow vehicle hitch, by cranking down on the tongue jack until the tongue is fully separated from the tow hitch ball.

12. 12

    Move the tow vehicle away from the camper.

13. 13

    Check level forepart to dorsum.

14. xiv

    Crank the handle on the tongue jack clockwise to raise the tongue terminate of the camper and counter clockwise to lower as necessary to achieve level. ^[ii]

Ad

1. i

   Pull out your campers electrical cord and run it to the electrical hookup on the campsite.

2. ii

   Turn off the billow at the campsite electrical hookup.

   • The campsite electric hookup is usually a three human foot tall post typically near the back of the military camp.
   • It is safer to plug your campers electric cord in with the breaker at the hookup off.

3. iii

   Plug your campers plug into the hookup and switch the billow dorsum on.

4. 4

   Switch the power on (the green 120 V switch) to your camper refrigerator at the back panel. This is especially important if you have food already in the fridge.

   • Almost camper refrigerators volition operate on 12V DC bombardment power (which does non work very well), every bit well as propane.

5. five

   Prepare out your outdoor carpeting or mat on the door side of the camper if yous are going to utilise ane.

6. 6

   Insert the end of the crank handle into the screw rod end of the camper back up.

7. vii

   Creepo down the 4 camper supports near to the ground without them completely touching yet.

   • This is to provide security for the camper (it will not tip) while still allowing the frame to flex while raising the roof.

8. 8

   Unlatch the four roof latches by pulling down the latch and pulling away the clip. ^[3]

9. 9

   Creepo up the camper roof. ^[iv]

   • This is washed using the same handle that you used to lower the supports. Information technology inserts into the roof crank spot at the dorsum of the camper.
   • Crank clockwise to raise the roof until it will not turn anymore and the roof is at it'due south total tiptop.

10. 10

    Crank down the iv camper supports the rest of the manner to the ground. You will experience some increased resistance when they contact the ground. Give them but a little snug later on that. There is no need to crank too tight.

    • These are located at the 4 corners of the camper near the bottom.

11. eleven

    Remove whatever items you need from the trunk of your camper if it has one. You will be pulling out the beds presently, and it will be more hard to remove things subsequently that.

Advertisement

1. i

   Grasp the handles on the outside end of one of the beds and pull it fully out until you feel a solid finish. As you pull information technology firmly out stay aware of the position of the canvas to make certain it is not communicable on anything. If something doesn't experience right Cease.^[five]

   • Check the canvass, pull information technology away from anything it could catch.
   • Check the inside of the camper to exist sure the bed isn't communicable on something.
   • It is necessary to pull firmly, simply if it'due south not moving, something is wrong. Don't force it.

2. 2

   Pull out the complimentary stop of the bed back up pole which is underneath the bed.

   • Position the free terminate of the support pole onto the stud on the frame of the camper.
   • Repeat this with the 2nd support pole.

3. iii

   Elevator upward on the bed to fully latch both supports. You volition feel the bed come upwards as you elevator and then it will sit down solidly when y'all gear up it down.

4. four

   Pull out the second bed using the same steps equally the showtime.

5. 5

   Pull out and twist the ii latches to release the slideout (if your camper has i).

6. half dozen

   Grasp both handles on the slide out lift slightly and pull out until you experience a solid stop.

7. 7

   Adhere the velcro on the canvass to the slide out to secure it.

8. viii

   Hook the bungee cords on the bed canvas to the hooks underneath the beds to secure the canvas.

9. 9

   Insert the end of the interior sheet support pole onto the canvas back up frame at the end of the bed and elevator.

10. 10

    Push out on the pole while positioning the other end into the back up clip.

    • Repeat this procedure with the other bed.

11. eleven

    Unsnap the door from the ceiling of the camper and carefully lower it into the door opening.

12. 12

    Turn the locking clips on top left and right sides of the door so they engage the slots to hold the door securely.

13. 13

    Attach the velcro on the canvas to the outside of the door frame.

Ad

1. i

   Catch the handle on the galley, lift and slowly lower information technology into position.

2. ii

   Take the outdoor stove (if you are using ane) to the hookup spot on the side of the camper.

   • This spot is on the door side of the camper. The stove sits about waist level.

3. 3

   Angle the front of the stove down while lifting the back and set it on the support while slowly lowering information technology downward. The lower bracket will remainder on the side of the camper and volition experience secure.

4. 4

   Connect the male cease of the propane hose on the outdoor stove to the female propane fitting on the lower frame of the camper.

5. 5

   Open the valve on top of the propane tank. Requite the propane lines a few minutes to equalize pressure in the system earlier turning on or using anything requiring propane.

   • The propane tanks are located at the front terminate of the camper.

6. 6

   Connect a sanitary h2o hose from your camper to the water spigot (if there is one on your campsite) and open the valve.

   • The hose hookup spot on the camper is on the side opposite the door side and near the dorsum end.
   • Switch on power to your camper'south h2o pump if yous don't take a h2o spigot and are going to exist using your water tank instead.
   • This switch is located within the camper adjacent to the galley.

7. 7

   Connect a bleed hose onto the drain fitting on the outside of the camper.

   • The drain fitting is on the back side of the camper. Your sink drains out of this fitting.

8. 8

   Connect the cease of the hose to a grey h2o tank or bucket.

Advertizement

1. one

   Open up the cover on the outside of the camper to access the hot water tank.

   • The access console is located near the forepart of the camper on the side opposite the camper door.

2. ii

   Push down and turn the gas knob to pilot and concur down. ^[6]

3. three

   Place a flame on the end of the airplane pilot tube that is pointing to the within, using a long lighter and wait till the airplane pilot stays lit. Be sure to go along holding down the knob while doing this.^[7]

4. iv

   Plough the knob to on. The hot water tank should go into full burn mode and begin heating the water.

   • If the pilot goes out, turn the gas knob to off and look five minutes before repeating procedure.
   • NEVER light a lighter or bring in an open up flame if you lot odour propane.

Advertising

Add New Question

• Question

  Is it possible to army camp in a pop upwardly without opening the finish beds?

  

  No. When the beds are not pulled out, there is no interior space inside the camper. The canvas will have null to attach to.

• Question

  I have my camper cranked all the mode up, how do I lower it?

  

  If you were able to creepo it all the mode up yous should exist able to do the verbal same thing in the reverse direction to lower information technology back downwardly. If it is stuck, you lot may have to expect and see what may be causing it to stick.

• Question

  How do I get the superlative of my pop-up camper unstuck?

  

  WD40 works well, or some kind of oil. Sometimes it can aid a lot to have other people pushing likewise.

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

• Its a really good idea to have a spotter watching equally you move the camper around. Sometimes its hard to see everything.

• Keep in mind when selecting a location for the camper that king size beds pull out near half dozen feet.

• Setting up at nighttime is much more difficult than in the solar day. Give yourself enough fourth dimension.

• If you lot are using your own water tank exist sure to retrieve to fill upward when you enter the campground.

Advertisement

• Practice not forget to unlatch the roof before you creepo information technology up. The lifting cables will get damaged.

• If y'all odor propane or doubtable a leak plow off your propane tank valve and extinguish any open flames.

• Keep people away from the camper as yous move it, particularly if you are backing upwardly and don't have full vision.

• Practice not set up too close to the fire pit.

Advertisement

Things Y'all'll Demand

• Pieces of plywood about 10"x 18" for leveling. These tin be of various thickness.
• RV drinking water hose. If your campground has a h2o hookup you will be using.
• RV extension cord. These are helpful when the electrical hookup is likewise far abroad, which is often.
• Level. Many can be permanently mounted to the camper tongue.
• Pocket-size two by iv woods pieces for blocking the wheels.
• Long nosed lighter for lighting the pilot on the water heater.

About This Article

Article Summary X

Setting up a new popular up camper at a campsite can experience intimidating, but working methodically can make the process go smoothly. Before you unhook your tow vehicle, position the camper where y'all desire it on your camp. Check the side to side level. If one side is depression, back the camper up a little, identify a piece of plywood where you want the bike, and motility frontwards again. Repeat this procedure until the camper is level. One time information technology'due south level, place modest blocks of forest in front and behind both wheels and so the camper won't movement. Then, swing the camper tongue jack downward and creepo the handle clockwise to raise the tongue end or counterclockwise to lower it to level the camper from front to back. To acquire how to fix the camper's beds and canvas, keep reading!

Did this summary help y'all?

Thanks to all authors for creating a page that has been read 54,095 times.

Did this article aid you?

Source: https://www.wikihow.com/Set-Up-a-Pop-Up-Camper

Share this post